Adj Vizi BSW 300 handleiding
Handleiding
Je bekijkt pagina 20 van 36
SYSTEM MENU
System Menu: When making adjustments press ENTER to conrm your setup then press and hold
the MENU button for at least 3 seconds. To exit without making any adjustments press the MENU
button. The display will lock after 30 seconds, press the MENU button for 3 seconds to unlock.
DMX SETTINGS -
DMX Address - With this function, you can adjust the desired DMX- address via the Control Board.
1. Access the main menu, and press the UP or DOWN buttons so that “DMX Setting” is highlighted, then
press ENTER.
2. Press the UP or DOWN buttons until “DMX Address” is displayed, and press ENTER. The current DMX
address will now be displayed.
3. Use the UP or DOWN buttons to adjust the DMX address.
4. Press ENTER to conrm or press MENU button to return to the main menu.
DMX Channel Mode - With this function, you can select your desired DMX channel mode.
1. Access the main menu, and press the UP or DOWN buttons so that “DMX Setting” is highlighted, then
press ENTER.
2. Press the UP or DOWN buttons until “DMX Channel Mode” is displayed, and press ENTER. The current
DMX channel mode will now be displayed.
3. Press the MENU button to return to the main menu.
DMX State - This mode can be used as a precaution mode, that in case the DMX signal is lost, interrupted,
or power is lost, the operating mode chosen in this setup is the running mode the xture will go into when
the DMX signal is lost. You can also set this as the running mode you would like the unit to return to when
power is applied.
1. Access the main menu, and press the UP or DOWN buttons so that “DMX Setting” is highlighted, then
press ENTER.
2. Press the UP or DOWN buttons until “DMX State” is displayed, and press ENTER. Use the UP and
DOWN buttons to switch between the two modes; Blackout or Hold. Press the ENTER button to make
your selection.
• LAST STATE - If the DMX signal is lost the xture will stay in the last DMX setting. If power is applied
and this mode is set, the unit will automatically go into the last DMX set up.
• BLACKOUT - If the DMX signal is lost or interrupted, the unit will automatically go into stand by mode.
• Master/Slave - If the DMX signal is lost or power is applied, the unit will automatically go into Master
Slave mode and run a built-in show.
3. Press the MENU button to return to the main menu.
SHOW SETTINGS -
Show Mode - Select a desired preset show to run.
1. Access the main menu, and press the UP or DOWN buttons so that “Show Setting” is highlighted, then
press ENTER.
2. Press the UP or DOWN buttons until “Show Mode” is displayed, and press ENTER. The current setting
will now be displayed.
3. Use the UP or DOWN buttons to nd your desired show. Shows 1-4 are factory shows, while Show 0 is
a random show.
4. Press ENTER to conrm your selection or press the MENU button to return to the main menu.
Slave Mode - Use this mode to set the unit as a “Master”, “Slave 1” or “Slave 2”
1. Access the main menu, and press the UP or DOWN buttons so that “Show Setting” is highlighted, then
press ENTER.
2. Press the UP or DOWN buttons until “Slave Mode” is displayed, and press ENTER. The current setting
will now be displayed.
3. Use the UP or DOWN buttons to nd your desired setting. Selecting “Slave 2” will give the unit contrast
movement to the “Master”:
4. Press ENTER to conrm your selection or press the MENU button to return to the main menu.
20
Bekijk gratis de handleiding van Adj Vizi BSW 300, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Adj |
| Model | Vizi BSW 300 |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 6572 MB |
