Adj Monster Duo handleiding
Handleiding
Je bekijkt pagina 8 van 10
ADJ Products, LLC - www.adj.com - Monster Duo Instruction Manual Page 15
Monster Duo Operation
Show Mode: In this mode you can choose 1 of 12 show modes to
run.
1. Press the MENU button until “Show Mode” is displayed, and
press ENTER.
2. Press the UP or DOWN buttons until you nd your desired show,
and press ENTER then press and hold MENU for 3 seconds to
con rm. See page 11 for more info.
With this feature you can connect the xtures to one another
using the I.E.C input and output sockets. The quantity that
can be connected is 12 xtures maximum for 120V and 20 x-
tures maximum for 240V. After the maximum xtures has been
reached you will need to use a new power outlet. They must be
the same xtures. DO NOT mix xtures.
Monster Duo Power Cord Daisy Chain
ADJ Products, LLC - www.adj.com - Monster Duo Instruction Manual Page 14
Operating Modes: The Monster Duo can operate in three dif-
ferent modes. In each mode you can run the fixture as a stand
alone fixture or in a master/slave confiugration. This next sec-
tion will detail the differences in the operating modes.
• Sound Active mode -
The fixture will react to sound, chasing through the built-in programs.
• Show mode -
Choose 1 of 12 show modes to run.
• DMX control mode -
This function will allow you to control each individual fixtures traits
with a standard DMX-512 controller such as the Elation® Show
Designer.
™
Universal DMX Control: This function allows you to use a Elation®
universal DMX-512 controller to control the chases and patterns,
dimmer and strobe. A DMX controller allows you to create unique
programs tailored to your individual needs.
1. The Monster Duo can is a 1 channel DMX fixture. See page 16
for detailed description of the DMX values and traits.
2. To control your fixture in DMX mode, follow the set-up procedures
on pages 6-8 as well as the set-up specifications that are includ-
ed with your DMX controller.
3. Use the controller’s faders to control the various DMX fixture traits.
4. This will allow you to create your own programs.
5. Follow the instructions on page 10 to set the DMX address.
6. For longer cable runs (more than a 100 feet) use a terminator on
the last fixture.
7. For help operating in DMX mode consult the manual included
with your DMX controller.
Sound Active Mode: This mode allows either single unit or several
units linked together, to run to the beat of the music.
1. Press the MENU button until “Sound State” is displayed, and
press ENTER.
2. Press the UP or DOWN buttons to choose either OFF or ON, and
press ENTER, then press and hold MENU for 3 seconds to con-
rm. To adjust sound sensitivity see page 11.
Monster Duo Operation
Master-Slave conguration This function will allow you to link up
to 16 units together and operate without a controller. In Master-Slave
operation one unit will act as the controlling unit and the others will
react to the controlling units programs. Any unit can act as a Master
or as a Slave.
1. Using approved DMX data cables, daisy chain your units togeth-
er via the XLR connector on the rear of the units. Remember the
Male XLR connector is the input and the Female XLR connector
is the output. The rst unit in the chain (master) will use the female
XLR connector only - The last unit in the chain will use the male
XLR connector only. For longer cable runs we suggest a termina-
tor at the last fixture.
2. Set the Master unit to your desired operating mode.
3. For the slave units press the MENU button until “Slave Mode”
is displayed, and Press ENTER. Set the slave units to either
“Slave 1” or “Slave 2”.
4. The slave units will now follow the Master unit.
Bekijk gratis de handleiding van Adj Monster Duo, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Adj |
| Model | Monster Duo |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 1498 MB |
