Abus HYP-E handleiding
Handleiding
Je bekijkt pagina 8 van 50
13 14
Do not immerse the helmet and accessory components in water.
• The helmet lights are a supplementary feature and do not replace the legally required
lighting equipment on bikes.
• Only use spare parts from ABUS.
11. Battery instructions
These products contain:
- Helmet HYP-E: 3.7 V lithium polymer battery (capacity 1600 mAh)
- Remote Control Indicator Light: 3.7 V lithium polymer battery (capacity 70 mAh)
- Remote Control Brake Light: 3.7 V lithium polymer battery (capacity 70 mAh)
Radio frequency: 2,4 GHz, transmission power 0dBM.
• Do not charge or use the product in environments where there is a risk of explosion, e.g.
from ammable liquids, gases or dust. Never burn the product! The battery could explode
in the re. This would also release toxic substances.
• Only use a suitable standard micro USB C charging cable in conjunction with a suitable
charger (5V DC power supply unit) for charging! Do not leave the product unattended
while it is charging!
• Do not use or store the products in areas where the temperature could reach below -20°C
or above +50°C. Do not expose the product to direct sunlight for long periods of time.
12. Replacement of battery and light using ABUS spare parts, g. Info 7.
For safe use of the helmet, it must be in its original condition again aer replacement.
The adjustment system must be xed again and the helmet shell must be securely
connected to the inside of the helmet at the intended points. If you have any questions,
please contact your specialist dealer or ABUS customer service
Fig. 7.1: Undo and remove the screws with a Phillips screwdriver.
Fig. 7.2: Remove the shell from the back to the front, as it is hooked in at the front.
Fig. 7.3: Disconnect both plug connections by pulling them out and not turning them
Fig. 7.4: Move the adjustment system all the way down to access the hole for removing the
lights. Pull the rail out of the guide, otherwise the hole cannot be reached.
Fig. 7.5: Use a blunt object, e.g. a pencil, to push the lights out through the existing holes
at the front and rear. Do not use a sharp object as this can damage the lights
Fig. 7.6: The new light can be installed. Insert the lights into the device provided. The
same applies to the battery.
Fig. 7.7: Reconnect both plug connections (press, do not twist!)
Fig. 7.8: The shell can be reattached from front to back.
Insert the shell into the device provided.
Fig. 7.9: Replace the screws using the Phillips screwdriver. Tighten them to 0.3 – 0.5 Nm.
13. Be careful when using magnets
ATTENTION: Magnets can damage credit cards or other cards
with magnetic strips. Magnets can also have an adverse eect
on pacemakers or other implanted devices. So ensure
sucient distance (approx. 20 cm) between the magnet
and the implanted devices – Danger to life!
14. Disposal
This product contains valuable raw materials. At the end of its service life, dispose of
the product in accordance with the applicable legal requirements. Electrical appliances,
rechargeable batteries and batteries must not be disposed of with household waste.
Disposal must be carried out in accordance with Directive 2012/19/EU on waste electrical and
electronic equipment (WEEE), or Directive 2006/66/EC on batteries and accumulators and
waste batteries and accumulators. Please contact the local authority responsible for dis-
posal if you have any queries. You can obtain information on collection points for your old
appliances, for example, from the local municipal or city administration, the local waste
disposal companies, or your specialist dealer. Dispose of the packaging according to type.
Separate the cardboard, foil and plastic elements for recycling.
15. Warranty
ABUS products are designed, manufactured and tested in accordance with applicable
regulations with great care. The warranty exclusively covers faults that are caused by
material or manufacturing defects. If a material or manufacturing defect can be proven,
the product will be repaired or replaced at the discretion of the warrantor. In such cases,
the warranty ends with the termination of the original warranty period. Any further claims
are expressly excluded.
ABUS assumes no liability for defects or damage that has been caused by external inu-
ences (e.g. transport, external forces), improper use, normal wear and tear or non-com-
pliance with this operating and installation instructions document. If a warranty claim
is asserted, the product must be returned with the original receipt with date of purchase
and a brief written description of the fault.
Information regarding ICES certification for Canada
CAN ICES-003 (B) Contains IC: 33614-HYPE
Contains IC: 33614-RCIL
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject
to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause
undesired operation of the device.
Subject to technical alterations. No liability for mistakes and printing errors.
Bekijk gratis de handleiding van Abus HYP-E, stel vragen en lees de antwoorden op veelvoorkomende problemen, of gebruik onze assistent om sneller informatie in de handleiding te vinden of uitleg te krijgen over specifieke functies.
Productinformatie
| Merk | Abus |
| Model | HYP-E |
| Categorie | Niet gecategoriseerd |
| Taal | Nederlands |
| Grootte | 9456 MB |
